*

Smith and also Wesson design 41 Target Pistol maintenance


*
Step #2
*
Step #3
*
Step #4 Lift the barrel assembly turn off of the structure and set it aside. clean or inspection deserve to be performed on the barrel assembly independently from the remainder of the pistol. A breech put cleaning rod or deep chamber cleaning is best completed at this time.

You are watching: Smith and wesson model 41 disassembly

*
Step #5
*
Step #6 The on slide assembly is now relocated forward to different it indigenous the frame.The pistol is currently separated right into it"s three main contents - barrel, frame, and also slide.
*
Step #7 Reassembly is accomplished in turning back order.Place recoil feather assembly on frame and also then install the on slide onto the frame
*
Step #8
*
Step #9
*
action #10
*

Back to peak of page

Slide detailed Disassembly and also Reassembly

Click picture to enlarge picture

Step #1 On the best side that the slide, situate the crosspin and also drift it left v a non-marring punch.
*
Step #2 Drift the crosspin completely out of the slide assembly. Through the crosspin eliminated the shooting pin and also spring will certainly drop the end of the bottom the the slide.
*
Step #3 Use a non-marring beat to drift the bolt assembly forward, out of the slide.
*
Step #4 Once the extractor claw clears the slot, the bolt assembly can be eliminated from the slide.
*
Step #5 Once the bolt is removed from the slide, the extractor claw have the right to be removed.
*
Step #6 The extractor plunger and plunger spring have the right to be removed from the slide slot.
*
Step #7 The bolt assembly is composed of the following components - shooting pin and return spring, extractor plunger and also spring, extractor hook, bolt housing, and crosspin (also serves as the firing pin stop).
*
Step #8 To reassemble the slide. An initial install the extractor spring and also plunger.
*
Step #9 Place extractor hook onto the bolt housing.
*
Step #10 Carefully slide the bolt housing and also extractor into the slide. When seated, location the crosspin in the left side of slide to save the bolt hosted in place. Take treatment to ensure the grooved end of crosspin is positioned outward.
*
Step #11 Turn on slide assembly over, ar firing pin and also spring into the bolt with the groove facing upwards.
*
Step #12 Use a tool to push in the shooting pin, press in the crosspin to lock the firing pen in place.
*
Step #13 Use a non-marring punch to seat the crosspin right into the slide till it sits flush through the next of the slide. Slide reassembly is complete.
*

Back to height of page

Trigger adjustment Procedures

Click image to enlarge photo

Step #1 First field strip the pistol as defined above. Climate loctate the trigger pivot pin. The pivot pin have to be drifted from the right towards the left next of the frame. It only has to be drifted part means to change the cause pull on the model 41.
*
Step #2 The trigger adjustment lever is situated inside the frame. Drifting the cause pivot pin approximately fifty percent way across the structure will enable clearance for adjustment lever movement.
*
Step #3 Lay some masking tape ~ above the ideal side of the structure to prevent any kind of surface marring from tool slippage.
*
Step #4 Use a 3/32" pin beat to drift the pivot pin.
*
Step #5 Drift the cause pivot pin part means into the frame.
*
Step #6 Ensure the trigger pivot pen is clean of the convey lever.
*
Step #7 Adjustments can be made by moving the bar forwards or rearwards in the frame. Each bar graduation is roughly 1/4 lb of adjustment. The create can be changed between 2 - 3 pounds by selecting an proper lever position.
*
Step #8 Once the preferred lever place is selected, drift pin to best far enough to check the cause pull. Make more adjustments as vital by relocating the pin and also lever.
*
Step #9 Once wanted pull load is achieved, drift the cause pivot pin to the right until the pin is flush through the left next of the frame. Reassemble pistol and test accordingly by live firing.
*

Back to height of page

Extractor Tuning convey Procedure

Click picture to enlarge picture


This procedure was very first developed to assist reduce S&W version 41 ejection difficulties by the late pistolsmith Austin Behlert. remove the slide from the pistol by field stripping. Check the extractor’s holding capacity by put a ring under the hook on flush on the bolt face. Gently shake the slide back and forth. If the situation falls off, climate the extractor is not to holding the cases securely against the bolt face. The extractor deserve to be tuned by using the complying with steps.
Remove the extractor hook native the bolt assembly by following the on slide disassembly direction above.
Place the extractor hook in a drill push vise. Tighten the vise jaws down just enough to put a slight bending (or bow) in the earlier side the the extractor hook – a couple of thousandths of an inch is every you’re trying to accomplish by this process. Fist – end tightening the vise jaws will break the M-41 extractor!
Use a pointed pen punch and tap that lightly through a hammer, in a stippling action, to make tiny dimples along the back side that the extractor. This dimples relieve the strain on the hardened steel and permit the extractor to conform come the new shape without having actually to re-heat treat it.
Next lightly paper the roughened dimples to smooth the end the extractor’s surface. Submit the extractor surface permits it to relocate smoothly when inside the slide’s extractor slot. Re-blue the extractor after ~ filing and also replace that in the bolt.

Back to peak of page

Magazine Disconnector Operation

*
The create bar is compelled downwards by the newspaper disconnector bar when a magazine in no installed. The magazine disconnector lever is spring invited to press downwards. As soon as the cause bar is under the sear is disengaged, and also the hammer cannot be exit by an operator pulling the trigger. The optimal (curved shark fin) section of the cause bar likewise has a disconnector function. As soon as the on slide is the end of battery the fin is compelled downward through the slide, this disconnects the sear and also prevents the pistol from being discharged.

See more: 2 3 E 4 5 I 6 8 What Is The Next Value 2 3 E 4 5 I 6 8, What Is The Next Value

*
The create bar is compelled upwards when a magazine is installed. The magazine disconnector lever is thrust upwards through the trigger bar return spring. Once the create bar is up, the sear is now involved by it and also the hammer deserve to be exit by an operator pulling the trigger. The peak (curved shark fin) portion of the cause bar is now aligned with the cut-out recess in the slide. Once the slide is closeup of the door it"s in battery, this allows the sear to be engaged by the create bar and also the pistol can be discharged.

Back to top of page