I have a question, and also I would really love for someone to help me. I have a 1997 Toyota Camry. 4 cylinder. The time belt obtained hung up and also shredded. When I go to replace the belt, ns noticed that ns couldn't turn the cam sproket gear by hand. I had to placed a wrrench top top it just to turn, and also when that did finally turn, that made a 1/4 turn, then seem to have actually freed up. Then got hung increase again. Is this the an outcome of a bending valve? and also, once everything is ago in place, what is the correct way to set the timing?


You are watching: 2001 toyota camry timing belt marks


The 1.5L and also 1.6 DOHC room interference engines which means if the belt division you have bent valves. The 1.6 SOHC and the 1.8 engines space not interference engines. Examine out the guide listed below to check out the marks and also instructions.https://www.charline-picon.com/diagrams/toyota/camry/1997Please operation down this guide and also report back.

Installation clues on the crankshaft to set the timing. Time belt diagram because that my car it has actually a 2.2 engine needed.
*

Hello, below is a guide and some diagram (below) That reflects the alignment of the crankshaft to the camshaft.https://www.charline-picon.com/diagrams/toyota/camry/1996You will have to jack the vehicle uphttps://www.charline-picon.com/articles/jack-up-and-lift-your-car-safelyand remove the harmonic balancerhttps://www.charline-picon.com/articles/how-a-harmonic-balancer-worksThe diagrams listed below will display you exactly how to execute the jobPlease allow us recognize if you need anything rather to acquire the difficulty fixed.Cheers, Ken
*

*

go to change timing belt ~ above camry and noticed the there it seems ~ to be odd tiiming marks on both the crank and also cam. On the camer gear, there are three marks, 2 on the teeth which are 6 teeth apart and then over there is a feet in one of the "spokes" top top the electronic came gear. Through the camshaft seal over there are also two marks; one is a divet and also another looks favor a drilled hole.Now top top the crank, there is a dot on the pulley and a little mark on the block. I have lined up the gears to what I believe are their particular marks but the engine still will certainly not start. That feels as if there is no compression. Ns don"t think there are any kind of bent valves, ns just believe the crank/cam are not time correctly. Please aid with the timing marks
If you timing belt is quiet on and the engine is to run okay, align the engine come number one TDC and verify the marks.
The belt broke, and aligning come TDC will only offer me the right mark on the crank, i beg your pardon still leaves finding the correct marks because that the cam.
it is challenging telling you without looking at them due to the fact that there are different marks. I imply you buy a Haynes publication for your vehicle. That will give the collection up. An excellent luck
A hands-on is your ideal bet top top this...too numerous litle details.https://www.charline-picon.com/kpages/auto_repair_manuals.htm
transmission problem1995 Toyota Camry 6 cyl two Wheel Drive hands-on where space the timing marks?We room shoulder deep in grease and also just waiting for her answer


See more: What Is The Main Religion In Southwest Asia, Religion In Southwest Asia & Northern Africa

OK, had actually to placed a new head on my 95 Camry LE through a 2.2. The head is set just fine and also the vehicle starts yet runs an extremely rough and also I"m acquiring a small "pop" and also "chug" ago through the main air entry while to run so the valves have to be slightly off. It"s not awful however it"s there. I have worn the web and also your website out looking for answers. The the next I have actually come is a thread on Toyota country http://www.toyotanation.com/forum/103-3rd-4th-generation-1992-1996-1997-2001/180435-camshft-timing-marks-5sfe.html my cams room lined up precisely as they are in the attached image from that thread. I"ve to be stuck in ~ this suggest for days and simply have to obtain the Camry to run again. I"ve looked for pics the would present me electronic came lobe positions once #1 Cyl is TDC however can"t find any. I have actually of a service manual PDF however it isn"t helping. It needs to be other simple. I"m not a mechanical moron however this one has me stumped and also lack of info isn"t helping.